Vinyl Intermediate Coating Supplier in China
Vinyl Intermediate Coating paint coating manufacture Shenzhen China  
Home About Us Products Contact Us

 

 




Honest Joy Coating & Paint
Vinyl Coating

Vinyl Fouling Topcoat
Vinyl-Aliphatic Urethane Primer and Finish Coat
Vinyl Wash Primer
Vinyl Red Oxide Primer

Vinyl Intermediate Coating
Vinyl Anti Fouling Topcoat
Vinyl Acrylic Based Exterior Flat Finish
Thin-Film Vinyl Ester Coating
Thick Vinyl Ester Coating
Solvent-thinned Chlorinated Vinyl Toluene-acrylate Low Lustre Coating
Self-etching Zinc Chromate Pigmented Vinyl Wash Primer

Reinforced Trowel Applied Vinyl Ester Lining
Premium Quality Full-bodied Smooth-flowing Vinyl-acrylic Primer
Abrasion Resistant Vinyl Ester Coating
Catalyzed Vinyl Ester Primer
Chlorinated Vinyl Toluene-acrylate Low Lustre Coating

High-hiding Non-bridging Premium Plus Vinyl Flat Finish
Catalyzed Vinyl Ester Primer
Epoxy Vinyl Primer

  

Vinyl Intermediate Coating

PRODUCT SPECIFICATIONS:

Product Description
FX-8120 is a phisically drying topcoat based on a vinyl
copolymer resin.
Recommended Use
As a versatile topcoat for vinyl systems on exterior steel
structures exposed in moderately to severely industrial
and marine corrosive environment.
Outstanding Characteristics
- High corrosion resistance
- Excellent water resistance
- Good appearance
- Good flexibility
Surface Preparation
The surface must be clean, dry and free from any
contamination such as grease, rust, mill scale, salt and
loose paint.

Technical Data

 

Finish

 Flat

Colour

 Upon request

Volume Solids

33 ± 2%

Specific Gravity

1.35 ± 0.05 gr/cm3

Flash Point

23 °C

Recommended D.F.T.

40-60 microns

Theoretical coverage

8.25-5.5 sqm/lit 6.11-4.07 sqm/kg

Practical Coverage

Depends on loss factor

Touch dry

2 hrs at °C

Hard dry

24 hrs at °C

Thermal resistance

80°C

Shelf life

12 months at 25°C

Package

liter container

Application Details

 

Application method

Air/Airless spray, Brush, Roller

Nozzle orifice Nozzle pressure

.019"-.021" 150 bar / 20 Psi

Application temperature

10 - 40 °C

Mixing ratio

single pack

Thinner/Cleaner

FX-80

Pot life

N/A

Recoat interval

Min 24 hrs Max 2 months

Application Procedure FX-8120
1. Flush all equipment with recommended cleaner before use.
2. Stir the product thoroughly with a power mixer.
3. For conventional spray, thin with no more than 10-15% of
recommended thinner for workability. For airless spray 5% of
thinner is normally sufficient.
4. Apply a wet coat by parallel passes. Overlap each pass 50%
to avoid bare areas, pinholes or holidays.
5. Double coat all welds, rough spots, sharp edges, rivets,
bolts, etc. to ensure proper thickness.
6. Check thickness of dry coating with a non-destructive dry
film thickness gauge. Recoat if greater thickness is required.
Note: If the maximum recoating interval is exceeded,
roughening of the surface is necessary to ensure intercoat
adhesion.
7. Random pinholes, holidays and small damaged or bare areas
can be touched up by brush when the film is dry to touch.
Larger areas should be resprayed.
8. In confined areas ventilate with clean air during application
and drying until all solvents are removed.
9. Clean all equipment with recommended cleaner immediately
after use.
Limitations
Surface temperature must be at least 3°c above dew
point.
Relative humidity during application should be less
than 80%.
Do not apply coatings under reverse environmental
conditions.
Safety
This product is flammable. Keep away from heat
and open flame. Keep container closed. Avoid
prolonged and repeated contact with skin.
Since improper use and handling can be hazardous
to health and cause fire or explosion, safety
precautions included with application instructions
must be observed during all storage, handling, use
and drying periods.
If used in confined areas:
- circulate adequate fresh air continuously during
application and drying.
- Use fresh air masks and explosion proof
equipment
- Prohibit all flames, sparks, welding and smoking
- Take precautionary measures against static
discharges
Keep away from food products.
Storage and Handling
The products must be stored in accordance with
national regulations.
The products should be kept in a cool and well
ventilated place protected from heat and direct
sunlight. Containers must be kept tightly closed.
Handle with care. Stir well before use.
Remarks
The information in this data sheet is given to the
best of our knowledge based on laboratory testing
and practical experience.
However we reserve the right to change the given
data without notice.
Any recommendation relating to the use of the
products, is based on data believed to be reliable. It
is buyer to satisfy itself of the suitability of the
product for its own particular use .
As the product is often used under conditions
beyond our control, we cannot guarantee anything
but the quality of the product itself.

 



Contact Us
 
Honest Joy Coating & Paint. All rights reserved.