Vinyl Wash Primer Supplier in China
Vinyl Wash Primer paint coating manufacture Shenzhen China  
Home About Us Products Contact Us

 

 




Honest Joy Coating & Paint
Vinyl Coating

Vinyl Fouling Topcoat
Vinyl-Aliphatic Urethane Primer and Finish Coat
Vinyl Wash Primer
Vinyl Red Oxide Primer

Vinyl Intermediate Coating
Vinyl Anti Fouling Topcoat
Vinyl Acrylic Based Exterior Flat Finish
Thin-Film Vinyl Ester Coating
Thick Vinyl Ester Coating
Solvent-thinned Chlorinated Vinyl Toluene-acrylate Low Lustre Coating
Self-etching Zinc Chromate Pigmented Vinyl Wash Primer

Reinforced Trowel Applied Vinyl Ester Lining
Premium Quality Full-bodied Smooth-flowing Vinyl-acrylic Primer
Abrasion Resistant Vinyl Ester Coating
Catalyzed Vinyl Ester Primer
Chlorinated Vinyl Toluene-acrylate Low Lustre Coating

High-hiding Non-bridging Premium Plus Vinyl Flat Finish
Catalyzed Vinyl Ester Primer
Epoxy Vinyl Primer

  

Vinyl Wash Primer

PRODUCT SPECIFICATIONS:

A two component pretreatment primer for use on properly prepared steel, aluminum
and galvanized metal.
For industrial and commercial use including piping, structural steel, marine vessels,
storage tank exteriors and roof decking. For use as a pretreatment primer to promote
adhesion of recommended topcoats on steel, aluminum and galvanized metal.
Vinyl Wash Primer is a reactive pretreatment which etches and passivates the substrate
and improves the adhesion of recommended topcoats. Fast drying for quick recoat time.

Dark Green
Flat
Nonvolatile - By weight - 19.5 ± 1.0%
By volume - 9.8 ± 1.0%
VOC (Calculated) - 5.92 lbs./gal.
710 grams/liter
Flash Point - 60o F
Weight per gallon - 7.5 ± 0.2 lbs.
Recommended Film Thickness per coat - 0.5 mils dry, 5.1 mils wet
Theoretical Coverage @ 0.5 mils dry - 314 sq. ft./gal.
Method - Brush or conventional or airless spray
Thinner - HJ-1701
Dry time @ 75oF - To touch - 5 minutes
To handle - 15 minutes
To recoat - *30 minutes
Note: See “Topcoating” section on back page
Consists of - 1 Gallon Unit 5 Gallon Unit

Unit Shipping Weight 9 lbs. 42 lbs.
Shelf Life - 12 months minimum from date of manufacture when maintained in protected
storage @ 40-100oF (subject to reinspection thereafter).
APPLICATION INSTRUCTIONS

Limitations: Apply in good weather when air and
surface temperature are above 40oF and surface
temperature is at least 5oF above the dew point. For
optimum application properties, material should be
between 70o to 100oF prior to mixing and application.
Maintain unmixed material in closed containers in
protected storage at 40 - 100oF.
Surface Preparation: Good surface preparation is
essential to a satisfactory coating system. Surfaces to
be coated should be clean and dry. Remove all oil,
grease, mildew or other contamination by solvent or
detergent cleaning or other effective means.
Steel - For best performance, application to abrasive
blasted surface is recommended. “Commercial Blast
Cleaning” (SSPC-SP6) is recommended as the minimum.
Proper blast media and blasting equipment shall be used
to produce an average profile depth of 1.5 mils minimum.
Do not reuse abrasive media. Remove blasting dust and
grit from surfaces before painting. Blasted surfaces
should be coated within 8 hours after blasting or before
rusting or other contamination of the surface occurs. If
blasting is not feasible, remove rust, mill scale .
Galvanized Steel - Remove all oil or other contamination.
Aluminum - Clean thoroughly to remove oil or other
contamination.
Previously Finished Surfaces - This coating must be
applied directly to properly prepared surfaces above.
Any previous coating must be completely removed.
Mixing: VINYL WASH PRIM is supplied in 2
containers as a unit. Always mix a complete unit in the
proportions supplied. (1) Agitate Part A Resin Component
with power agitator. Special care should be taken to
completely redisperse any settled pigments. (2) Combine
entire contents of part A with entire contents of and Part
B Acid Component and mix thoroughly with power agitator.
Material should be used within 8 hours.
Thinning: This product is supplied at normal spraying
viscosity. If thinning is necessary thin with HJ-1701.
Application: Apply by brush or conventional or airless
spray. Apply at a spreading rate of approximately 314
square feet per gallon which will yield a dry film thickness
of 0.5 mils.
Topcoating - Allow this coating to dry 12 hours before
topcoating with epoxy coatings containing strong
solvents. This product is not designed for exterior
exposure and should be topcoated within 24 hours.
Equipment: Brush - Use a good quality bristle brush.

Cleanup: Clean all equipment immediately after use
with HJ-1701. Completely flush all spray
equipment with this solvent. Occasional flushing of spray
equipment during the course of the working day helps
prevent buildup and possible clogging.
Safety: Safe storage, handling and use dictate that
adequate health and safety precautions be observed
with this product and any recommended thinners. User
is specifically directed to consult the current Material
Safety Data Sheet for this product as well as precautions
contained on product labeling.
Notice: The technical data contained herein are true
and accurate to the best of our knowledge. All products
are offered and sold subject to our Conditions of Sale. Published
technical data and instructions are subject to change
without prior notice.

 



Contact Us
 
Honest Joy Coating & Paint. All rights reserved.