Water Based Two-Component Epoxy Polyamide Finish Supplier in China
Water Based Two-Component Epoxy Polyamide Finish paint coating manufacture Shenzhen China  
Home About Us Products Contact Us

 

 




Honest Joy Coating & Paint
Waterborne Coating

Waterborne Satin Enamel
Water-Borne Premium Quality Acrylic Primer
Water-Borne High Performance Interior Acrylic Primer Undercoat
Two-Part Water-Borne Linear Polyurethane Enamel

Water-Borne Epoxy Primer
Water Reducible Urethane Primer
Water Reducible Enamel
Water Miscible Epoxy Coating
Water Borne Inorganic Zinc Rich Silicate Primer
Two-Component Water-Borne Epoxy Primer

Water Based Two-Component Epoxy Polyamide Finish
Water-Borne High Performance Acrylic Metal Primer
Water Based Gloss Epoxy Enamel

Urethane Modified High Solids Water Borne Coating
Water-Borne High Performance Acrylic Metal Primer
Water Borne Acrylic Protective Coating
Arylic Thermo Plastic Waterbase Finish
Self-Levelling Epoxy Flooring Water Borne
Acrylic Water borne Paint Eggshell Waterborne Interior Paint
Environmentally Friendly Waterborne Metal Primer
Fast Drying Interior Exterior Primer
Acrylic Water borne Paint
High Gloss Waterborne Aliphatic Polyurethane Enamel

  

Water Based Two-Component Epoxy Polyamide Finish

PRODUCT SPECIFICATIONS:

DESCRIPTION:
A water based, two-component epoxy polyamide that is chemical resistant and provides a tough, durable gloss finish
for interior surfaces. Water Reducible Epoxy is best when used on primed or previously painted surfaces of masonry,
concrete, brick, unglazed tile, plaster, wallboard, iron and steel. It is ideal for schools, hospitals and other areas where
a high performance, low odor coating is needed. Product features water clean-up and easy application with brush,
roller or spray.

SPECIAL CAUTIONS:
Should not be used on ductwork or similar surfaces subject to considerable flexing and vibration. Avoid the use of
solvents to thin material.
Do not attempt to extend pot life by refrigeration.
Do not apply when material, surface air or temperature is below 60° F. (15° C.) or if relative humidity is above 85%.
Keep packaged material from freezing.
SURFACE PREPARATION:
GENAL - Surface must be clean and dry. Remove oil, grease and wax with paint thinner. Remove dirt by
washing with a detergent solution. Rinse thoroughly with clear water and allow to dry. Rust should be removed by
wirebrushing or sanding. Refer to "Surface Preparation Guide" for more detailed instructions.
UNFINISHED SURFACES:
MASONRY-POURED AND PRE-STRESSED CONCRETE - Surfaces should be clean and dry. Etch all surfaces with
a mixture of 2 parts water and 1 part muriatic acid. After etching action stops, wash the surface thoroughly with fresh
water and allow to dry. Fill all pits and air holes with Latex Cement Patching Compound. Allow to cure overnight. If the
concrete has not aged, prime with latex primer and allow to dry at least two hours before topcoating.
BLOCK-CONCRETE, HAYDITE, AGGREGATE - Be sure surface is clean and free of mud, dirt, dust or other foreign
matter. Cracked joints or blocks should be repaired.
Normal Service - Dry with Occasional Splash Spillage. Surface should be filled with latex block filler. Avoid the
formation of a layer of filler on the block face. Allow Block Filler to dry overnight before topcoating.
Severe Service - Continually High Moisture Areas: Surfaces should be filled with epoxy block filler. Allow block filler to
dry overnight before topcoating.
ASBESTOS-CEMENT BOARD, BRICK AND UNGLAZED TILE - Surface must be clean and dry. See Mixing and
Reducing instructions.
PLAST, GYPSUM WALLBOARD, DRYWALL AND SHEETROCK - Surface must be clean and dry. Prime with
latex primer and allow to dry overnight.
WOOD, PLYWOOD, HARDBOARD, PARTICLE BOARD AND OTH WOOD DIVATIVES - Surfaces must be
clean and dry. Prime with primer undercoat and allow to dry overnight.
IRON AND STEEL - Remove rust and corrosion by sandblasting, scraping, wire brushing or sanding. Prime with one
coat of metal primer and allow to dry overnight.
GALVANIZED METAL AND GLAZED TILE - Surface must be clean and dry. Prime with vinyl wash primer. Allow to
dry one hour before topcoating.
PREVIOUSLY FINISHED SURFACES:
Remove all loose and flaking paint by scraping and sanding. Sand Glossy finishes until dull. Spot check for lifting of
old finish. If lifting occurs, remove old finish with stripper and treat as new wood.
MIXING AND REDUCING:
Mix 1 part of "A" (Base) Component to 1 part "B" (Catalyst) Component by volume. Allow to stand 30 minutes before
using or reducing. Mix no more material than will be needed for use in one working day. Do not attempt to extend pot
life by refrigeration. Reducing is normally not required for brush, roller or airless spray application. For conventional
air spray, water may be added up to one pint per converted gallon of material.
APPLICATION:
Do not apply when surface, air or material temperature is below 60° F. (15° C.) or if relative humidity is above 85%.
Water Reducible Epoxy may be applied by brush, roller, and conventional or airless spray application. Two
applications are required for best appearance. Use a short nap roller cover on smooth surfaces. Use the following
spray recommendations or equal as a guide.
AIRLESS SPRAY:
Tip . . . . . . . . . . . . . . . .013-.015"
Fan . . . . . . . . . . . . . . 50°-60°(10-12 inch fan)
Pressure . . . . . . . . . . 1800-00 PSI
CLEAN UP:
Clean all equipment immediately after each use with warm soapy water, then rinse with clean water. Follow-up with
mineral spirits in spray equipment to avoid rusting. Dispose of used paint and waste in accordance with local, state
and federal regulations.
COVAGE:
One gallon of converted Water Reducible Epoxy should be applied at an application rate of 300-400 square feet per
gallon (27-36 square meters per 3.785 liters) per coat on smooth surfaces. Approximate dry mil thickness of 2.2 to 1.7
mils at recommended spreading rate of 300 to 400 square feet per gallon per coat.
DRYING:
Optimum drying conditions are 60° F. to 90° F. (16° C. to 32° C.) at 50% R.H.
To Touch . . . . . . . . . . . . . . 1 Hour
To Recoat . . . . . . . . . . . . . . 4 Hours
Lower temperatures and high humidity will slow dry.
DESCRIPTION:
A water based, two-component epoxy polyamide that is chemical resistant and provides a tough, durable gloss finish
for interior surfaces. Water Reducible Epoxy is best when used on primed or previously painted surfaces of masonry,
concrete, brick, unglazed tile, plaster, wallboard, iron and steel. It is ideal for schools, hospitals and other areas where
a high performance, low odor coating is needed. Product features water clean-up and easy application with brush,
roller or spray.
Values based on Water Reducible Epoxy Polyamide White
Weight Gallon: 13.00
Weight Solids: 62.5%
Volume Solids: 40.3%
Coverage:
@ 1 Dry Mil: 647 sq. ft./gallon
@ Spread Rate: 350 sq. ft./gallon (4.0 mils wet)
Deposits a 1.6 mil dry film
VOC (g/l): Not to Exceed 380
Viscosity: 100-105 K.U. @ 77° F.
Gloss @ 60: 85+
Grind (Hegman): #7
DOT Class: Non-Combustible, Not Regulated
Specification: N/A

Cure Time (Based on 70° F. & 50% R.H.):
To Touch: 1 Hour
To Recoat: 4 Hours
Recommended Thinner: Water for clean-up and reduction for spray
Temperature Resistance: Continuous 150° F., Intermittent 0° F.
CAUTION! Do not take internally. Close container after each use. Use only with adequate ventilation. KEEP OUT
OF THE REACH OF CHILDREN. For specific safety requirements, refer to the Material Safety Data Sheet. Protect
from freezing.
LIMITATION OF LIABILITY: To the best of our knowledge, the technical data contained herein is true and accurate at the date of
issuance, but is subject to change without prior notice. We make no guarantee of any kind, express or implied, including
merchantability and fitness for particular purposes. Liability, if any, is limited to replacement of the product or refund of the
purchase price. Labor, or cost of labor, and other consequential damages are hereby excluded.

 



Contact Us
 
Honest Joy Coating & Paint. All rights reserved.