Water-Borne High Performance Interior Acrylic Primer Undercoat Supplier in China
Water-Borne High Performance Interior Acrylic Primer Undercoat paint coating manufacture Shenzhen China  
Home About Us Products Contact Us

 

 




Honest Joy Coating & Paint
Waterborne Coating

Waterborne Satin Enamel
Water-Borne Premium Quality Acrylic Primer
Water-Borne High Performance Interior Acrylic Primer Undercoat
Two-Part Water-Borne Linear Polyurethane Enamel

Water-Borne Epoxy Primer
Water Reducible Urethane Primer
Water Reducible Enamel
Water Miscible Epoxy Coating
Water Borne Inorganic Zinc Rich Silicate Primer
Two-Component Water-Borne Epoxy Primer

Water Based Two-Component Epoxy Polyamide Finish
Water-Borne High Performance Acrylic Metal Primer
Water Based Gloss Epoxy Enamel

Urethane Modified High Solids Water Borne Coating
Water-Borne High Performance Acrylic Metal Primer
Water Borne Acrylic Protective Coating
Arylic Thermo Plastic Waterbase Finish
Self-Levelling Epoxy Flooring Water Borne
Acrylic Water borne Paint Eggshell Waterborne Interior Paint
Environmentally Friendly Waterborne Metal Primer
Fast Drying Interior Exterior Primer
Acrylic Water borne Paint
High Gloss Waterborne Aliphatic Polyurethane Enamel

  

Water-Borne High Performance Interior Acrylic Primer Undercoat

PRODUCT SPECIFICATIONS:

A water-borne high performance acrylic primer/undercoat, for interior use over primed metal and as a primer
undercoat over joinery and under Interior Acrylic Gloss. Also used as a primer undercoat under
selected products within the Colorfects range.
AVAILABILITY
Colour Range Refer to current Literature
Packaging 2.5 litre
PROPTIES
Drying Time Under normal drying conditions touch dry 1 hour and recoatable after 4 hours. Allow
for adequate ventilation during the drying period.
Finish Matt
Composition
Pigment: Titanium Dioxide and extenders.
Binder: Acrylic polymer
Solvent: Water.
Spreading Rate 16m² per litre depending on smooth surfaces.
Wet Film Thickness 62 micrometres at 16m² per litre.
Dry Film Thickness 18 micrometres at 16m² per litre.
Volume Solids 28%
Flash Point Not applicable
VOC Content limit value for this product (cat.A/d): 150 g/l (07) / 130 g/l (10) This product
contains max. 17 g/l VOC.
Limitations For interior use only. Do not apply when there is a risk of rain, air or substrate
temperatures are likely to fall below 8ºC or when the relative humidity is above 80%
during application or the drying period
PREPARATION
New Surfaces Timber
All surfaces must be suitably dry, and free from anything that will interfere with the
adhesion of the materials to be applied. Rub down with a suitable grade of abrasive
paper. Remove all dust. Treat knots with two thin coats of fresh knotting. Fill any fixing
holes, open joints and shallow surface defects with Ready Mixed Filler.
Rub down with a suitable grade of abrasive paper. Remove all dust.
All metals including galvanised
Surfaces must be clean and free from anything that will interfere with the materials to
be applied. Wash with hot water and liquid detergent solution to remove oil, grease or
any other contaminants, frequently changing the water. Rinse thoroughly with clean
water. Allow to dry. Galvanised surfaces should be pre-treated with Decorators
Choice Passivating Wash. Overall blackening of the surface will confirm satisfactory
surface preparation.
Additional surface preparation – all metals
Non-ferrous metals
Lightly abrade to a bright (not polished) surface – excluding galvanised surfaces.
Rinse thoroughly with clean water to remove all resides. Allow to dry. Prime with one
coat of Water Based Metal Primer.
Ferrous metals
Remove all millscale and rust back to clean metal. Remove all residues. Prime within
the working day with one coat of Water Based Metal Primer.
Previously Decorated Surfaces Timber
All surfaces must be suitably dry, and free from anything that will interfere with the
adhesion of the materials to be applied. Remove all loose, and failing or suspect
paint. Remove grey and denatured surfaces by rubbing down with abrasive paper.
Feather edges of sound paint. Remove all dust. Organic growth must be removed and
the areas treated with Fungicidal Solution. Treat knots with two thin
coats of fresh knotting. Fill any fixing holes, open joints and shallow surface defects
with Ready Mixed Filler. Rub down with a suitable grade of abrasive
paper. Remove all dust. Spot prime all bare and filled areas with one coat of Water Based Primer Undercoat.
Metals
All surfaces must be suitably dry, and free from anything that will interfere with the
adhesion of the materials to be applied. Remove all loose, and failing or suspect
paint. Feather edges of sound paint. Remove all dust. Remove all rust. Spot prime
non-ferrous metals including galvanised metal with one coat of Water
Based Metal Primer.
Timber and metals
Wash remaining sound paint with hot water and liquid detergent solution to remove
any contaminants, frequently changing the water. Any glossy or eggshell surfaces
must be wet abraded to provide a key. Rinse with clean water to remove all residues.
Allow to dry. Bring forward spot primed areas with one coat of Water
Based Primer Undercoat.
COATING SYSTEM Apply one or two coats as required.
APPLICATION Stir well before use. Apply using a good quality fine filament synthetic brush to an even
thickness. On timber lay off in the direction of the grain.
CLEANING Return surplus material to container. Wash with clean water immediately after use.
HEALTH AND SAFETY Please refer to the Safety, Health and Environmental Information on the container.
Take special precautions during the surface preparation of pre 1960’s painted surfaces
as they may contain harmful lead. For further information contact the
Customer Relations Team. When preparing all surfaces avoid the inhalation of dust
and/or metal particles. Wear a suitable facemask. Material Safety Data Sheets for this
and all other Honest joy products are freely available from the place of purchase or
the address below. Store in secure dry conditions inaccessible to children or animals.
Containers should be kept closed during storage. Do not empty into drains,
watercourses or access routes to septic tanks.
GENAL INFORMATION Under normal and frost free conditions this
product will remain usable for up to two years if stored correctly and unopened.
Every care is taken to ensure that all information provided on this Technical Data
Sheet is accurate. Honest joy is unable to guarantee results as it has no control
over the conditions under which its products are applied.
Before using this product please ensure you have the latest information.

 



Contact Us
 
Honest Joy Coating & Paint. All rights reserved.